12A

"XJDano" (xjdano) 03/10/2014 at 16:25 • Filed to: None

0

23

on my way to buy 12A rotary for $45 not sure what I'm going to do with it

AndersSim - V10'ING > XJDano 03/10/2014 at 16:26

0

Doesn't matter, I bought an old Mercedes wheel cap for the equivalent of 40$ last Friday. No idea why, but I found a spot for it in the garage.

Party-vi > XJDano 03/10/2014 at 16:28

1

Pull the engine apart and make some end tables with each rotor?

philipilihp > XJDano 03/10/2014 at 16:42

0

I would LOVE a rotor. Just cuz. I think that's plenty of reason, so I applaud you!

Textured Soy Protein > XJDano 03/10/2014 at 16:43

3

Some ideas...

phenotyp > XJDano 03/10/2014 at 16:51

0

XJDano > phenotyp 03/10/2014 at 17:10

0

too heavy

Nick, Drives a Cobalt LT > XJDano 03/10/2014 at 17:15

0

Sell ikt to me so I can put it in my truck....please.....

XJDano > Nick, Drives a Cobalt LT 03/10/2014 at 17:19

0

come & get it, $5 finders fee.

Nick, Drives a Cobalt LT > XJDano 03/10/2014 at 17:29

0

What state?

XJDano > Nick, Drives a Cobalt LT 03/10/2014 at 17:31

0

St.Louis, MO

Nick, Drives a Cobalt LT > XJDano 03/10/2014 at 17:32

0

Fucking Hell......

I want that engine so bad......I want to rotary swap my truck..... haha

XJDano > Nick, Drives a Cobalt LT 03/10/2014 at 17:32

0

it was set up for NOS if you didn't see that yet

!!! UNKNOWN CONTENT TYPE !!!

XJDano > Nick, Drives a Cobalt LT 03/10/2014 at 17:37

0

where are you?

Nick, Drives a Cobalt LT > XJDano 03/10/2014 at 17:37

0

New Hampshire.

pdthedeuce > XJDano 03/10/2014 at 23:32

0

go-cart !

roflcopter > XJDano 03/11/2014 at 02:31

0

If you want to sell it to a good home, I made a post about a project I want to start the other day. I promise it'll be epic!

XJDano > roflcopter 03/11/2014 at 21:06

0

Where are you at? I was going to try and make something cool with the rotors, or something. But wouldn't mind too much if it gets running again.

I have no immediate plans for it as I already have 2 blocks ahead of it, I just couldn't pass it up for $45

roflcopter > XJDano 03/12/2014 at 00:46

0

I'm in Florida sadly...

Although I'm sure arrangements could be made. I've been wanting to do a p-port 12A build for forever... and a cheap motor that I don't mind milling housings on is EXACTLY what I need. Does it turn over by hand? If so, it has at least a 70% chance of being rebuildable without major issues.

XJDano > roflcopter 03/12/2014 at 08:34

0

I'll try it when I get some time.
Not opposed to the idea, but you'd have to let me drive it when its done.

roflcopter > XJDano 03/12/2014 at 10:25

0

Sweet! Just let me know! I'm honestly not sure where the engine would end up, either I pick up a stripped miata chassis and it goes towards an autocross killer, or it ends up in the Lemons car, or I yank the engine in the Volvo 240 currently in the garage and confuse everyone(wouldn't that just be hilarious?).

XJDano > roflcopter 03/16/2014 at 11:15

0

My neighbor across the street may be going to FL in a few months. I still haven't took a closer look at the motor, but where in FL are you? not sure where he is going, but I'll find out when I pay him for installing doors on my rental house.

roflcopter > XJDano 03/16/2014 at 11:33

0

I'm in the panhandle. But it'd only be a bit of a drive for me to meet somewhere on his way if he were going down south. Or... We could ship it greyhound!!! Bahahahaha

XJDano > roflcopter 04/27/2014 at 21:17

0

cleaning garage and the 12A spins freely enough that I can spin the clutch by hand, so the apex seals may not be great, but its not seized. Still on your radar? I may take it off the dolly and shove it under the jeep for now.

My neighbor across the street did say that he sold his house and will be out by may 15th. Not sure if/when he plans on heading to FL. you can e-mail me at moc.liamg @ ttibbarjx spelled backwards obviously, that'll go right to my phone.